FC 1030 triple mower conditioners

FC 1030 mower conditioner profile

Maximum output, optimal forage

Available in three widths (from 8.33 m to 9.93 m), they ensure maximum output without compromise on the quality of the harvested forage. They are intended for contractors, machinery cooperatives and large farms. To chose from: a conditioner with fingers or rollers.

Find a dealer near you

Areas to mow are increasingly becoming larger while optimal mowing periods are becoming more limited. What about the forage quality?
When considering that lowering the level of impurities from 4 to 2 % per year, results in gaining 89€/ha/year*, it is essential that farms harvest forage without impurities.
You can count on the performance,quality of work and reliability of our range.
FC triple gang mowers help you to reach your goals in terms of output and quality - without compromise.
FC triple gang mowers are available in three versions, designed for tractors from 120 hp: FC 8730 (8.33 to 8.73 m); FC 9530 (9.13 to 9.53 m); FC 10030 (9.53 to 9.93 m). Attach a FC 3125 F or a FC 3525 F at the front of the tractor to benefit from the same techniques as the rear unit!
FC 10030 at work

Your benefits

Maximum work output, optimal forage quality

The LIFT-CONTROL suspension system

The key to clean forage: LIFT-CONTROL hydro-pneumatic suspension

Lowering the level of impurities from 4 to 2 % per year, means gaining 89€/ha/year*. With the LIFT-CONTROL hydro-pneumatic suspension system, controlling the impurities is no longer a problem. It is far more than a suspension system, using an accumulator instead of the traditional spring.
The exclusive kinematics of the triple gang mowers in this range include a cylinder for the suspension of the mowing unit (1), a safety release cylinder (2), an accumulator with adjustable pressure (3) and a pivot point strategically positioned close to the machine's centre of gravity (4).
The adjustment adapted by the suspension system limits the introduction of impurities in the forage and reduces the ground pressure of the cutter bar, therefore a reduction of the fuel consumption and skid wear, and the sward is preserved.
*Researchers from the Chamber of Agriculture of Weser Ems (Germany) have carried out a study in a german forage producing region. They compared 2 silages, one with a level of impurities of 2 % and the other with 4 % in order to determine the financial impact on a dairy farm. After having measured the nutritional value of the silage of poorer quality, they calculated the value of concentrates that needed to be added in order to reach the same level of milk production.

OPTIDISC ELITE: the unrivalled cutter bar

The new OPTIDISC ELITE cutter bar has been developped with farmers/users. The different disc spacing, large overlap areas and low mowing angle provide the required quality of cut. Fitted with this cutter bar including its latest upgradings, the triple FC 1030 ensures a clean and regular cut in all situations.
  •  Where the discs diverge, the spacing is reduced for a larger knife overlap area. Clean and regular cut even in short or light forage (A).
  •  Where the discs converge, the spacing is larger to facilitate the flow of forage which is quickly ejected rearwards: the mowing work is not affected (B).
  • Overlap area nearly doubled for improved quality of cut on wet or sticky soils (or in the presence of molehills) or in heavy or lying forage, plant covers harvested in late autumn.
  • A smaller pitch angle: when mowing at a relatively flat angle, it prevents creating typical undulating mowing profiles. This development also promotes a smoother and faster regrowth and easier adjustment of the following machines.
  • New disc bearings with exclusive shape and fastening always ensure that knives are secured in case of shocks while giving them 360-degree freedom of rotation.
In hilly terrain, in wet conditions or sticky grass, soil can build up in front of the cutter bar, except with OPTIDISC ELITE! Its specific skids improve sliding and preserve the sward. Another benefit for forage quality, especially in difficult conditions.
Variable spacing on the OPTIDISC cutter bar

Ground following with the travel range of the rear units

The rear units of the FC triple gang mowers follow nearly all ground contours, due to the following characteristics:
  • units with pendulum type articulation,
  • hydraulic side offset of 20 cm,
  • vertical offset of nearly 50 cm,
  • angular range of approximately 20° with an overlap of 50 cm.
Impressive figures that prove that KUHN has done everything possible to improve the quality of your forage!
Perfect ground following, especially on slopes

Adjustable swath widths

The mowing unit swath width can be reduced to a minimum of 1.00 to 1.20 m. This is so the tractor wheels do not run over the already formed swath. The forage remains intact without introducing any impurities.
The FC 10030 forms narrows swaths

Time and money savings

Travel range of the NON-STOP safety system

Combined LIFT CONTROL and NON-STOP safety

Nobody can afford to damage their mower because of an obstacle or a wrong manoeuvre.
On hitting an obstacle, the concerned mowing unit pivots rearwards around an axis (4). At the same time, the oil is transferred to the LIFT-CONTROL suspension system cylinder. The resulting pressure increase facilitates mower lift in order to clear the obstacle. The mowing unit automatically returns to its initial position without stopping.
  • The safety system remains efficient even if the obstacle is hit by the mowing unit's inner discs as the pivot point of the arm is far enough from the first discs (A).
  • The independent suspension of each mowing unit prevents the frontward acceleration of the opposite mowing unit when clearing the obstacle.
  • The hydraulic safety release can be adjusted according to mowing conditions. The cylinder can be fitted in two positions (arrows): the second position increases the power, required for the safety, for example during high speed work or in particularly difficult conditions.

Maximum reliability and stability

The cutter bar has been designed to cope well with obstacles. Being equipped with the PROTECTADRIVE safety system, in the event of a violent impact between a disc and an obstacle, the shaft holding the disc can shear just above the bearing thanks to a carefully dimensioned shear groove. Therefore the gear wheels are protected. In less than 15 minutes, the machine can back up and running with a low repair cost.
KUHN advantage: Disc-bearing stations are attached by long bolts that pass through the entire cutter bar. This eliminates any risk of the mounts being torn out of the cutter bar in the event of an impact. Top-of-the-range components strengthen the centre piece of the cutter bar:
  • Special disc-bearing station with a double row of angular contact ball bearings.
  • Large-diameter gearwheels in high-precision forged steel with 3 cogs engaged.
  • Forged and heat-treated discs.
  • Disc skids made from treated steel with the option of adding a bolt on protective layer.
In order to lengthen the machine's service life, shock absorbers are integrated in between the cutter bar and chassis. The structure of the machine is less affected by impacts, especially when working at fast forward speeds.
Shearing of the PROTECTADRIVE system

Minimum maintenance

You will waste no time on maintenance.
The OPTIDISC ELITE cutter bar is an excellent example of added value created through the close collaboration between manufacturer and farmer. It is a solution that is totally adapted to operations and will save you time:
  •  Lubricated for life. No need to service the cutter bar.
  • FAST-FIT quick-release knife system, 100 % secure. A powerful leaf spring provides constant pressure on the knife retainer for extra safety. It takes just a few moments to replace the knives.
Maintenance is kept down, and is occassionally necessary for the drive system and the pivot points.
FAST-FIT quick-release knife system

The FLEXPROTECT guard: save on repair costs

To avoid damage during mowing, around the edge of the fields or along trees, the outer FLEXPROTECT guard bends and then returns to its initial shape. This design avoids additional repair costs. Unfolding of the guards is controlled hydraulically.
The outer FLEXPROTECT guard

Conditioning adapted to your needs

FC 10030 at work, view of front-mounted machine

In difficult conditions: pivoting steel fingers

The 540 mm rotor with pivoting steel fingers offers exceptional conditioning capacity:
  • Uniform drying over a large widths even in difficult conditions.
  • The power requirement is limited for heavy or long forage.
  • The pivoting fingers avoid foreign bodies.
  • Forage delivered in swaths or widely spreading.
It can easily be adapted to the forage type with a two-speed central lever. Reducing the speed is ideal for delicate forage and to reduce the fuel consumption, for example for later mowing in lighter crops (755 min-1). The speed can be increased in dense forage (1000 min-1).
The conditioning rotor drive shaft is protected by a shear bolt therefore the machine and its drive are safe even in the event of impacts with foreign bodies.

For delicate crops: SQUAREFLEX rubber rollers

Integrating legumes in a ration reduces the quantity of concentrates to purchase.
A test carried out by Arvalis (the French agronomical institute) with the Chamber of Agriculture and the machinery cooperative FD in 2016 highlighted the drying patterns of different mower conditioners (finger or roller, in nylon or steel). The mower conditioner with a polyurethane roller came out top:
  • Saving of approximately 100 Euros / ha/cut with the rollers
  • Drying close to 80 % of DM from the second night comparing to the other methods which obtained this result after the third night.
Is this ennough to justify the purchase of a roller conditioner?
Thanks to the specific tread of the polyurethane rollers, the plants are crimped through a regular movement. Their large diameter provide significant capacity to evacuate the forage rearwards and prevent its wrapping around them.
The pressure adjustment between the rollers is made via an easy-to-access adjustment screw. In addition, the gap between the rollers can be widened to let foreign bodies pass through.
On a mechanical level, the rear roller is driven by 2 gearboxes and a maintenance-free drive. The upper roller is driven by a special gear train. Benefit from a life-long perfect synchronisation and reduced maintenance!
FC 10030 R with rollers in delicate alfalfa-type crops

FC 10030 at work rear view

Specifications

Technical characteristics
 
Working width (m) in combination with a front mower
Overlap between front and rear units (cm)
Transport width (m)
Transport height (m)
Cutter bar
Number of discs with heat treated protection skids
Disc skid lining
Blade attachment
Cutting height range with standard skids (mm)
Gear train protection system
Ground following
Suspension
Safety breakaway
Outer protection
Conditioning system
Conditioner speed (min-1)
Conditioner drive
Overall swath width (min/max) approx. (m)
Wide spreading system
Headland turning position
Conveyor belt drive
Forage delivered by conveyor belt
Operation and function control
Hitch
Machine parking
PTO speed (min-1)
Overload protection
Free wheel
Theoretical tractor power requirement (kW/hp)
Required tractor hydraulic connections
Required tractor electrical connections
Machine control
Speed signal
Road lights and signalling on rear
Approx. weight (kg)
FC 8830 D-FF FC 8830 R-FF FC 9330 D-RA FC 9530 D-FF FC 9530 R-FF FC 10030 D-FF FC 10030 R-FF
8.73 8.73 9.30 9.53 9.53 9.93 9.93
30 - 50 (FC 3125 DF) and 50 -70 (FC 3525 DF) 30 - 50 (FC 3125 RF) / 50 -70 (FC 3525 RF) 42 (FC 3125 DF) / 62 (FC 3525 DF) 30 - 50 (FC 3125 DF) and 50 -70 (FC 3525 DF) 30 - 50 (FC 3125 RF) / 50 -70 (FC 3525 RF) 30 - 50 (FC 3525 DF) 30 - 50 (FC 3525 RF)
2.95 2.95 3.00 2.95 2.95 3.35 3.35
Below 4 m
OPTIDISC ELITE OPTIDISC ELITE OPTIDISC ELITE cutter bar with FAST-FIT quick release, modular disc bearing stations removable from the outside and fitted with PROTECTADRIVE safety OPTIDISC ELITE OPTIDISC ELITE OPTIDISC ELITE OPTIDISC ELITE
2 x 7 (2 x 3.10 m) 2 x 7 (2 x 3.10 m) 2 x 8 (2 x 3.50 m) 2 x 8 (2 x 3.50 m) 2 x 8 (2 x 3.50 m) 2 x 8 (2 x 3.50 m) 2 x 8 (2 x 3.50 m)
2 - as standard on each cutter bar 2 - as standard on each cutter bar 2 - as standard on each cutter bar 2 - as standard on each cutter bar 2 - as standard on each cutter bar 2 - as standard on each cutter bar 2 - as standard on each cutter bar
FAST-FIT quick release FAST-FIT quick release FAST-FIT quick release FAST-FIT quick release FAST-FIT quick release FAST-FIT quick release
35 to 65 35 to 65 35 to 65 35 to 65 35 to 65 35 to 65 35 to 65
PROTECTADRIVE system PROTECTADRIVE system PROTECTADRIVE system PROTECTADRIVE system PROTECTADRIVE system PROTECTADRIVE system
Pendulum-type articulation Pendulum-type articulation Pendulum articulation Pendulum-type articulation Pendulum-type articulation Pendulum-type articulation Pendulum-type articulation
LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension LIFT-CONTROL hydro-pneumatic suspension
Non-stop safety Non-stop safety Non-Stop rearward and upward shifting safety system while at the same time lifting the cutter bar front Non-stop safety Non-stop safety Non-stop safety Non-stop safety
Hydraulic folding Flexprotect side guards
Pivoting steel fingers - adjustable conditioning plate with 5-position lever 2 polyurethane rollers with double synchronized drive Pivoting steel fingers - adjustable conditioning plate with 5-position lever Pivoting steel fingers - adjustable conditioning plate with 5-position lever 2 polyurethane rollers with double synchronized drive Pivoting steel fingers - adjustable conditioning plate with 5-position lever 2 polyurethane rollers with double synchronized drive
755 or 1000 adjustable by selector lever 780 755 or 1000 - adjustable by selector lever 755 or 1000 adjustable by selector lever 780 755 or 1000 adjustable by selector lever 780
By gearbox with anti-blocking safety By gearwheels By gearbox with anti-blocking system By gearbox with anti-blocking safety By gearwheels By gearbox with anti-blocking safety By gearwheels
2 x 1.45 / 2.10 2 x 1.45 / 2.10 2 x 1.85 / 2.40 2 x 1.85 / 2.40 2 x 1.85 / 2.40 2 x 1.85 / 2.40
As standard As standard As standard As standard As standard As standard
By hydraulic cylinders By hydraulic cylinders By hydraulic cylinders By hydraulic cylinders By hydraulic cylinders By hydraulic cylinders
By integrated hydraulic unit with pumps fitted on the central gearbox.
Belt position and speed adjustable from the cab. Possibility to modulate the belt speed according to the slope angle (manual compensation by the driver or automatic by standard built-in inclinometer)
To choose from: central delivery (width of 1.80 to 3.60 m), delivery with one side raised (18 m cut delivered over 12 m for raking by a 4-rotor rake), flat delivery
Individual lift of rear units and setting into transport position Individual lift of rear units and setting into transport position Individual lift of rear units and setting into transport position Individual lift of rear units and setting into transport position Individual lift of rear units and setting into transport position Individual lift of rear units and setting into transport position
3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) 3-point - Cat. 3 or 4N (Quick Hitch cat. 3/4N compatible) 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible) 3-point Cat. 3 and 4N (Quick Hitch Cat. 3/4N compatible)
Unfolded or folded on dedicated parking stands Unfolded or folded on dedicated parking stands Unfolded or folded in vertical position Unfolded or folded on dedicated parking stands Unfolded or folded on dedicated parking stands Unfolded or folded on dedicated parking stands Unfolded or folded on dedicated parking stands
1000 1000 1000 1000 1000 1000 1000
Primary PTO-shaft with torque limiter Primary PTO-shaft with torque limiter Torque limiter on primary PTO-shaft Primary PTO-shaft with torque limiter Primary PTO-shaft with torque limiter Primary PTO-shaft with torque limiter Primary PTO-shaft with torque limiter
Integrated in the side gearbox Integrated in the side gearbox Standard - on side gearboxes Integrated in the side gearbox Integrated in the side gearbox Integrated in the side gearbox Integrated in the side gearbox
140 / 191 140 / 191 154 / 210 154 / 210 154 / 210 162 / 221 162 / 221
2 DA valves (+ 1 DA optional for the tractor hydraulic top link) 2 DA valves (+ 1 DA optional for the tractor hydraulic top link) Rear machine LS connected: 1 x pressure, 1 x free return, 1 x load sensing
Front machine: 1 x SA (plus 1 x DA if hydraulically controlled Flexprotect side guards)
2 DA valves (+ 1 DA optional for the tractor hydraulic top link) 2 DA valves (+ 1 DA optional for the tractor hydraulic top link) 2 DA valves (+ 1 DA optional for the tractor hydraulic top link) 2 DA valves (+ 1 DA optional for the tractor hydraulic top link)
1 x 7-pin plug 1 x 7-pin plug Rear machine: 1 7-pin plug and 1 ISOBUS plug
Front machine: 1 7-pin plug
1 x 7-pin plug 1 x 7-pin plug 1 x 7-pin plug 1 x 7-pin plug
ISOBUS machine: use of a CCI terminal or ISOBUS-certified tractor terminal
via TECU (if ITH harness, plan a type B cable)
As standard As standard As standard As standard As standard As standard
3030 3150 3,98 3210 3330 3260 3380

Media

FC 10030 at work rear view